Level
43 parts
Time to create ~ 12 to 18 hourse
FOX ON THE MOON
490 x 150 x 530 mm
Paper side 2018. All rights reserved. This model (and instructions) are provided for the sole purpose of your personal pleasure.
Copying, selling, sharing privately or publicly are strictly prohibited without my authorisation. Thank you for your understanding.
GSPublisherEngine 0.43.100.63
THE PRINCIPLE
FOLD
FOLLOW THE
PAST NAMES
1
1
1
3
8
22
2
13
12
15
12
20
21
valley fold = fold up
mountain fold = fold down
FIND THE MATHING POINTS
SND CLUE TOGETHER
3
SCORE
8
CUT OFF
15
3
EQUIPMENT YOU’LL NEED
A4/letter
A4/letter
180-210 gsm
B&W
x13
180-210 gsm
A4/letter
x5
180-210 gsm
A4/letter
x1
regular
colour 1
colour 2
colour 3
white
MOON
BODY
EARS AND
PAWS
Instructions
(optional)
x7
Choose water-based glue
or
Better in metal, but let’s
not be too fussy here.
Avoid the lumpy glue sticks
and the dripping super glue
Toothpicks are optional but prove useful
to spread the glue evenly for example
or
or
TIPS & TRICKS
1
HOW TO SCORE
Use a ruler with / a dried out ball point pen / the tip of a pointy object (compasses) / the dull side of a knife or
X-acto knife. If it gets though the sheet, then this is not the right tool. Batch your pieces to save time.
2
PUT PARTS IN ORDER (FIRST PART ON TOP)
Pile the parts: 1 above, 16 below. This will also save your time later when you are in the heat of the action!
3
GLUE THE NON-PRINTED SIDE OF THE FLAPS
The printed side and the flaps are hidden inside the sculpture. So press the non-printed side of a flap
against the printed side of its matching edge.
4
ONE FLAP AT A TIME
Take the time to position a flap accurately. Wait for it to dry before you move on to the next one (5 to 7secs).
5
USE VERY LITTLE GLUE (ALONG THE OUT EDGE OF THE FLAPS)
A thin line of glue or a few tiny drops are more than enough, or it will spread and spoil the outside
of your sculpture. If it happens, scrape out the surplus with your nail, then rub the paper with a little saliva.
6
AVOID POTENTIAL OFFSETS OF THE PARTS
If one flap is slightly misplaced, it will increasingly affect each following edge. If this happens and your
glue has dried, don’t try to unstick the flap. Instead, try to adjust the offset bit by bit at the next flap onward.
Here is a good method to avoid offsets:
When adding a new part, take Firmly hold the corners first,
until the glue sticks (5 sec.)
a moment to be sure the
first flap aligns accurately and then press the rest.
with its matching edge.
7
Now that the first end of
the next tab is in place,
it will be easy to align the
second end of it.
Again, press the corner Keep holding it while aligning
first and wait 5 seconds. the middle of the tab. (when
AND OBVIOUSLY, KEEP YOUR HANDS CLEAN.
Regularly rub your fingers to get rid of the tiny dry bits of glue. Otherwise they will turn black, get on
to your sculpture and become difficult to remove.
LET’S GO!
2/7
GSPublisherEngine 0.43.100.63
it comes to longer flaps, press
for another 5 sec). Then press
back & forth between the 2 ends.
1
+2
+4
+5
+7
+8
+10
+11
MOON
+3
+6
+9
3/7
GSPublisherEngine 0.43.100.63
+12
+13
+15
+16
+14
FOX
Turn the front side of the item 17 and 18.
Paint over black color nose and eyes.
As the picture shows
23
15
28
39
28
15
39
24
53
12
52
26
14
40
87
14
13
14
16
27
33
22
68
16
52
26
34
18
48
16
40
14
49
29
29
22
27
33
51
93
16
13
19
13
41
42
55
80
20
17
21
80
95
56
42
116
35
96
+19
55
34
94
21
17
27
91
91
20
40
+18
27
41
32
21
94
81
40
34
17
21
19
31
32
116
39
92
51
93
81
19
31
39
13
19
49
34
9
10
30
24
18
12
6
48
67
33
29
12
49
20
22
22
49
33
56
99
43
98
10
38
57
0
36
99
105
93
91
98
0
10
38
43
11
5
37
5
96
57
11
35
95
36
105
95
91
92
93
37
17
42
95
92
3
41
81
94
10
17
42
104
10
0
41
81
94
10
96
10
0
104
104
78
101
10
6
80
104
99
101
96
78
99
10
6
10
10
2
79
1/6 (row1 col1)
1/6 (row1 col1)
97
4/7
98
77
GSPublisherEngine 0.43.100.63
97
98
80
2
79
77
67
29
31
18
2035
10
26
10
26
92
30
47
53
11
50
44
45
8
11
25
7
25
23
54
47
31
30
12
30
35
48
18
9
9
9
66
48
24
24
10
65
6
50
44
45
7
54
46
66
32
32
28
11
38
8
8
46
28
11
8
25
17
47
15
38
7
46
47
18
15
7
25
46
3
+20
+22
+21
+24
+23
+25
+26
+27
+28
+29
+30
+31
5/7
GSPublisherEngine 0.43.100.63
+32
+33
+34
+35
+36
+37
+38
+39
+40
+41
+42
+43
6/7
GSPublisherEngine 0.43.100.63
Attach the Fox to the moon, as shown in the picture
7/7
GSPublisherEngine 0.43.100.63
0
